11.16.2. Removal and installation of the dashboard
It will be required to you: TORX T25 key, a face head "on 10", "on 12", the screw-driver with a crosswise edge.
1. Disconnect a wire from the minus plug of the rechargeable battery.
2. Remove facings of forward racks (see. "Removal and installation of facings of salon").
3. Remove a steering wheel (see. "Removal and installation of a steering wheel").
12. Remove a steering column (see. "Removal and installation of a steering column").
|
13. Remove the control unit of external lighting (see. "Replacement of the control unit of external lighting").
|
14. Remove a combination of devices (see. "Removal and installation of a combination of devices") …
|
15. … also turn off a bolt of fastening of the dashboard to a framework.
|
16. Open a ware box …
|
17. … having wrung out fingers on both sides of a wall of a ware box, remove course limiters...
|
20. Turn off three nuts and remove an arm.
|
21. Disconnect a block of a plait of wires from a conclusion of a safety cushion of the forward passenger.
|
22. Remove a cable tip from an air temperature regulator gate drive axis …
|
23. … also disconnect from the heater case the holder of a braid of a cable.
|
24. Remove facing of a tunnel of a floor (see. "Removal and installation of facing of a tunnel of a floor").
|
25. Take the autoradio tape recorder from the central console of the dashboard (see. "Removal and installation of the autoradio tape recorder").
|
26. Remove the block of switches...
|
27. … and the holder of coins (see. "Replacement of switches of the dashboard").
|
Note
Depending on a complete set instead of the holder of coins the switch of system of dynamic stabilization (ESP) or a control lamp of shutdown of a safety cushion can be installed.
|
28. Turn out two screws of the top fastening of the panel to the central console …
|
29. … two screws of average fastening …
|
30. … and one internal screw of fastening.
|
31. Accurately hook the screw-driver the panel of the central console …
|
32. … and, overcoming resistance of metal clamps, take away the panel.
|
33. Disconnect a block of a plait of wires from a conclusion of the control unit of system of heating (conditioning) and ventilation of salon.
|
34. Disconnect a cable tip from the switch of the mode of an obduv …
|
35. … also remove an overlay of the central console assembled with the control unit of system of heating (conditioning) and ventilation of salon.
|
36. Turn out one screw of fastening of the left slip to the dashboard …
|
37. … hook the screw-driver a plastic clamp of the lower fastening of a slip …
|
38. … also remove a slip, having brought its latches out of holders on dashboards.
|
39. Remove rubber a sealant of a doorway and take them aside.
|
42. Turn out two screws …
|
43. … and one bolt on the left side of fastening of the dashboard to a forward rack.
|
44. Turn out one screw on the left side of fastening of a frame of a ware box to a dashboard framework.
|
45. Turn out the screw of fastening of the right overlay of the dashboard and sort the right side of the dashboard (see similar operations of subitem 36-43).
|
46. Turn out one screw on the right side of fastening of the dashboard to a panel framework.
|
47. Turn out two lower screws of fastening of the dashboard to a framework …
|
48. … also remove the decorative panel, overcoming resistance of plastic clamps.
|
49. Remove the left and right forward facings of thresholds (see. "Removal and installation of facings of salon").
|
50. Turn out bolts 1 and 3 fastenings of wires of "weight" to a dashboard framework. Take the holder 2 plaits of wires and take a plait aside. Turn out from the left and right side on two bolts 4 side fastenings of a framework of the dashboard to a forward rack …
|
51. … remove a cap and turn out an internal bolt of side fastening of a framework of the dashboard to the left forward rack of a body.
|
52. Similarly turn out a bolt of fastening of a framework on the right side.
53. Turn out two top bolts of fastening of a framework of the dashboard to the heater case.
|
54. Disconnect everything holders of a plait of wires from a dashboard framework. Turn out two central bolts of fastening of a framework of the panel to the basis of a body and take it from an aperture between racks.
|
55. Establish all removed details as it should be, the return to removal.